Broan-NuTone QTHB1 Guide d'installation

Naviguer en ligne ou télécharger Guide d'installation pour Kits de montage Broan-NuTone QTHB1. Broan-NuTone QTHB1 Installation Guide Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 2
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
MODEL QTHB1
ULTRA SILENT
TM
FAN - HANGER BAR KIT
For use with Broan or NuTone QT Fans & Fan Lights
TYPICAL INSTALLATIONS
Housing mounted anywhere
between I-joists
using hanger bars.
Housing mounted anywhere
between joists
using hanger bars.
Housing mounted anywhere
between trusses using
hanger bars.
Housing mounted anywhere
between trusses using
hanger bars.
INSTALLATION
1. Assemble slide channels and mounting
brackets to ventilator housing.
Attach the SLIDE CHANNELS to the housing using the
SCREWS supplied. Make sure TABS face “up” as shown.
Use the set of channel mounting holes (marked “STD”) to
mount the housing flush with the bottom of the drywall. Use
the other set of holes (not marked) to mount the housing
flush with the top of the drywall.
2. Fasten ventilator to framing.
Extend mounting brackets to the width of the framing.
Hold ventilator in place with the mounting brackets wrapping
around the bottom edge of the framing.
Nail ventilator to framing or fasten with screws (not provided)
through holes near nails.
*
To ensure a noise-free mount: Secure mounting brackets
together with screws or use a pliers to crimp slide channels
tightly around mounting brackets.
Connect ductwork, wiring, and finish installation following in-
structions supplied with the fan or fan/light.
NAIL (4)
HOLE FOR
OPTIONAL
SCREW
MOUNTING (4)
BROAN-NUTONE ONE YEAR LIMITED WARRANTY
Broan-NuTone warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of one year from the date of
original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE.
During this one-year period, Broan-NuTone will, at its option, repair or replace, without charge, any product or part which is found to be defective under normal use and service.
THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS, TUBES, HALOGEN AND INCANDESCENT BULBS, FUSES, FILTERS, DUCTS, ROOF CAPS, WALL CAPS AND OTHER
ACCESSORIES FOR DUCTING. This warranty does not cover (a) normal maintenance and service or (b) any products or parts which have been subject to misuse, negligence, accident, improper
maintenance or repair (other than by Broan-NuTone), faulty installation or installation contrary to recommended installation instructions.
The duration of any implied warranty is limited to the one-year period as specified for the express warranty. Some states do not allow limitation on how long an implied warranty lasts, so the
above limitation may not apply to you.
BROAN-NUTONE’S OBLIGATION TO REPAIR OR REPLACE, AT BROAN-NUTONE’S OPTION, SHALL BE THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. BROAN-
NUTONE SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE. Some states do
not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This warranty supersedes all prior warranties.
To qualify for warranty service, you must (a) notify Broan-NuTone at the address or telephone number below, (b) give the model number and part identification and (c) describe the nature of any
defect in the product or part. At the time of requesting warranty service, you must present evidence of the original purchase date.
Broan-NuTone LLC, 926 W. State Street, Hartford, Wisconsin 53027 www.broan.com www.nutone.com 800-558-1711
99044693A
TOOLS NEEDED
BOTTOM EDGE
OF FRAMING
*
SCREW (2)
HAMMER 1/4” HEX DRIVER
OR
PHILLIPS SCREWDRIVER
MOUNTING
BRACKET (4)
SCREWS (4)
TAB “UP”
STD
SLIDE
CHANNEL (2)
VENTILATOR
HOUSING
THIS KIT INCLUDES:
(4) MOUNTING BRACKETS,
(2) RH, (2) LH
(2) SLIDE CHANNELS
WITH SPACERS
SCREW PARTS BAG
assembled
as received
(4) SCREWS
Vue de la page 0
1 2

Résumé du contenu

Page 1 - MODEL QTHB1

MODEL QTHB1ULTRA SILENTTM FAN - HANGER BAR KITFor use with Broan or NuTone QT Fans & Fan LightsTYPICAL INSTALLATIONSHousing mounted anywhere bet

Page 2 - – KIT DE BARRA DE SUSPENSIÓN

MODELO QTHB1Montaje de la cubierta en cualquier parte entre armad-uras por medio de barras de suspensión.Montaje de la cubierta en cualquier parte en

Commentaires sur ces manuels

Pas de commentaire